Compact marker
Smart-Cube
The smallest marking platform we list — built for benches where floor space is the binding constraint.
- Laser power
- 20 W or 30 W versions
- Work area
- 70 × 70 mm to 110 × 110 mm, by configuration
Laser marking, engraving & cutting
A jewellery laser marking machine uses a 1064 nm fibre laser to mark brand logos, design and lot codes and customer names permanently into gold, silver and other metals — on flat pieces and, with a rotary device, inside rings. A laser cutting machine goes further and cuts right through the metal, for name pendants and cut-out designs. Semsons Tech supplies both, and our laser cutting machine has been recognised with a Best Laser Cutting Machine award.
Awarded Best Laser Cutting Machine — JMAIIE Excellence Awards Night, 2024
The range
The range covers four platforms. The Smart-Cube is described in our catalogue as the world's compact marking machine — built for benches where floor space is the binding constraint. Smart Cut handles precision jewellery and metal cutting. Smart Mark covers general marking and engraving across jewellery and metal parts. Smart-2 is a benchtop laser processing platform.
Marking and cutting sit at two different points in a jewellery workflow. Cutting shapes and separates metal early, during design and moulding; marking applies brand marks, design and lot codes, traceability codes and personalisation near the end, after the piece is finished. The sample pieces in our catalogue show exactly those jobs: inside-ring text, marks on bangles and bracelet plates for the Smart Mark, and name-plate and filigree pendants for the Smart Cut.
Compact marker
The smallest marking platform we list — built for benches where floor space is the binding constraint.
Laser cutter
Precision cutting of gold and other precious metals for name pendants and cut-out designs — the machine behind our Best Laser Cutting Machine award.
Workshop marker
Everyday marking and engraving: brand marks, lot codes, serial numbers and text inside rings.
Benchtop platform
A benchtop laser platform from 20 W to 60 W, for deeper engraving and higher volumes.
By job
Most buyers start with a job rather than a machine name. This is which of our lasers does which job.
| Job | Machine | Why |
|---|---|---|
| Brand logos, design and lot codes | Smart Mark, Smart-Cube | Fibre laser marking, 20 W or 30 W. Smart-Cube where bench space is tight. |
| Names and dates inside rings | Smart Mark, Smart-Cube, Smart-2 | With the optional rotary device, which turns the ring so the text runs evenly around the inside. |
| Deeper engraving and higher volumes | Smart-2 | 20 W to 60 W versions; higher powers for deeper engraving. |
| Names in Hindi, Gujarati, Tamil and other scripts | All three marking machines | The marking software supports Indian-language fonts. |
| Gold name pendants and cut-out designs | Smart Cut | Fibre laser cutter for reflective precious metals, 100 W to 300 W, 300 × 300 mm standard cutting area. |
| BIS hallmark and HUID | Not a jeweller’s laser | Applied only by a BIS-recognised hallmarking centre. Your own laser marks your brand, codes and customer names. |
Side by side
Every figure below is as published on each machine’s own page. Anything not shown is confirmed in writing with your quotation.
| Parameter | Smart-Cube |
Smart Cut |
Smart Mark |
Smart-2 |
|---|---|---|---|---|
| Type | Compact Laser Marking | Laser Cutting | Laser Marking | Benchtop Laser |
| Laser type | Fibre laser, 1064 nm | Fibre laser for cutting reflective precious metals | Fibre laser, 1064 nm | Fibre laser, 1064 nm |
| Laser power | 20 W or 30 W versions | 100 W, 200 W or 300 W versions | 20 W or 30 W versions | 20 W to 60 W versions; higher powers for deeper engraving |
| Work area | 70 × 70 mm to 110 × 110 mm, by configuration | 300 × 300 mm standard | 110 × 110 mm standard; 150 × 150 mm extended | 110 × 110 mm standard; 150 × 150 mm extended |
| Design | Compact marking head on a stand, with a separate controller box | Enclosed cabinet with viewing window | Not published | Open desktop unit with adjustable column and emergency stop |
| Rotary device for rings | Rotary device, optional | Not published | Rotary device, optional | Rotary device, optional |
| Thickness and speed | Not published | Confirmed in writing for your metal and design | Not published | Not published |
| Catalogue samples | Not published | Name-plate pendants, a filigree pendant, square earrings | Inside-ring text, bangles, rings, bracelet plates | Not published |
| Full page for Smart-Cube | Full page for Smart Cut | Full page for Smart Mark | Full page for Smart-2 |
Not sure which machine fits?
Tell us the jobs you will run and the metals you work in, and we will recommend a machine and send the current datasheet.
Equipment by business For jewellery retailers & gold buyers: the equipment we supply for this kind of business
Before you buy
Engraving inside a ring needs a fibre laser marker with a rotary attachment that turns the ring while it writes. Name pendants are cut from gold or silver sheet with a fibre laser cutting machine. Your own laser can mark your brand, codes and customer names, but never the BIS hallmark or HUID.
A HUID hallmark has three parts: the BIS mark, the purity grade such as 22K916, and a six-digit code unique to the piece. It is mandatory for gold sold in 392 districts, and only a BIS-recognised hallmarking centre can apply it, after XRF screening and fire assay. A jeweller's own XRF analyzer checks each lot before it goes for hallmarking. A jeweller's own laser marker is for brand and lot marks, never the hallmark.
Silver hallmarking in India is still voluntary in 2026. Since 1 September 2025, any silver piece that is hallmarked must carry a six-digit HUID beside the BIS mark and a purity grade such as 925, and more than 90 lakh pieces have been hallmarked that way. For a silver maker, the practical steps are to test each lot before it goes for hallmarking, keep alloys separate, and keep your own marks apart from the hallmark.
Answers
Written to be useful before you buy, not after.
Laser marking removes almost no material — it changes the surface to leave a permanent logo, design code, serial number or name, and happens near the end of production. The BIS hallmark itself is applied only by a recognised hallmarking centre. Laser cutting removes material to separate or shape metal, and happens early, around design and moulding. Different jobs, different machines: Smart Mark and Smart-Cube for marking, Smart Cut for cutting.
Stage eight of ten, alongside laser welding, tick welding and hydra welding. By that point the piece is cast, set and hand-polished; marking is applied before final polishing so any surrounding surface disturbance is cleaned up in stage nine.
Not for a jeweller. The BIS hallmark and HUID are applied only by a recognised Assaying and Hallmarking Centre, and BIS guidelines require a centre's hallmarking laser to be used for nothing else. A jeweller's own laser marks brand logos, design and lot codes and personalisation.
Yes, that is one of the jobs shown in our catalogue for the Smart Mark, with text marked inside rings. It needs a rotary device, which turns the ring so the text runs evenly around the inside; it is available as an option on the Smart-Cube, Smart Mark and Smart-2. Results depend on ring size, lettering and depth, so confirm the result on your own sample piece before you order.
The catalogue lists marking and cutting as separate machines with separate model names, and we do not claim one unit does both equally well. If you need both, tell us your volumes for each and we will advise whether two machines or one compromise platform makes more sense for your floor.
Yes. All our marking machines use 1064 nm fibre lasers, which suit gold, silver and other metals. Depth and finish depend on the metal, the design and the power you choose, so confirm the result on your own sample piece before you order.
We quote each machine in writing rather than list one price, because the figure moves with the configuration: the laser power (20 W or 30 W on the Smart-Cube and Smart Mark, 20 W to 60 W on the Smart-2, 100 W to 300 W on the Smart Cut), the work area, and whether you add the rotary device for rings. Tell us the jobs you will run and we will send a quotation with the current datasheet.
Yes. The software on our marking machines supports Indian-language fonts, so customer names and messages can be engraved in regional scripts as well as in English.
Get in touch
Tell us what you are producing and we will recommend the right model — including when the honest answer is that you do not need this machine yet.
Share your production requirement and we will come back within one working day with the right model, a realistic throughput estimate and a quotation.