Written on the factory floor

Insights & guides

Practical writing for people who run production — not marketing copy. If a figure comes from our catalogue we say so, and where we do not have data we say that too.

Guides
36
Topics
8
Latest

All guides

Automation

Looking for diamond setting labour? Hire setters, send job work, or set by machine

If you are looking for diamond setting labour, you have three choices: hire and train setters, send the setting out as job work, or set the small round stones in wax on an automatic machine before casting. Hand setting grows only when you add people; a machine adds output without adding setters.

· 6 min

Automation

What is wax setting in jewellery? How stones are set before casting

Wax setting means setting the stones into the wax model of a piece before it is cast, instead of into finished metal afterwards. When the metal is poured it forms around each stone and locks it in, so the piece comes out of casting already set. It suits designs with many small round stones made in quantity.

· 6 min

Technical

Rhodium plating for jewellery: the process step by step and what you need

Rhodium plating deposits a very thin layer of bright white rhodium on jewellery by electroplating. Most bad results come from poor cleaning, not the plating: polish, clean, degrease, activate and rinse before plating, and follow your rhodium solution's data sheet for voltage and time. Silver usually needs a barrier layer first.

· 4 min

Operations

How to photograph jewellery in a light box

A photography light box surrounds jewellery with soft, even white light, so polished gold and stones reflect clean light instead of the room. Clean the piece, fix the camera or phone on a stand, set the white balance, lock focus on the main stone, and use the same setup for every product so your catalogue matches.

· 5 min

Technical

How to test gold coins and bars without damaging them

Test gold coins and bars with two non-destructive checks. An XRF analyzer reads the gold percentage at the surface, and a conductivity tester looks below it. Tungsten conducts at about 18.8 MS/m, which matches neither fine gold (about 45) nor 22K coin gold (about 9.7), so a hidden tungsten core reads off target.

· 4 min

Buying guide

Ring engraving and name pendants: which laser machine does which job

Engraving inside a ring needs a fibre laser marker with a rotary attachment that turns the ring while it writes. Name pendants are cut from gold or silver sheet with a fibre laser cutting machine. Your own laser can mark your brand, codes and customer names, but never the BIS hallmark or HUID.

· 5 min

Buying guide

How to choose a wax injector machine for jewellery

Choose a vacuum wax injector with separate temperature control for the pot and the nozzle, an auto-clamp and stored settings for each mould. A tabletop digital injector suits small workshops, a larger tank suits long runs, chip-based mould settings suit many different moulds, and an automatic injector suits high-volume factories.

· 5 min

Operations

Buying old gold at the counter: a simple test routine before you pay

Test every piece of old gold before you pay and before you melt it. Check the hallmark and HUID, read the alloy on an XRF machine, watch for plated or filled pieces, weigh on a calibrated scale, and record the result with the customer. Once pieces are melted together, a low-purity piece can no longer be found.

· 4 min

Technical

Porosity in jewellery casting: gas or shrinkage, what causes it and how to fix it

Porosity has two main kinds. Shrinkage leaves tiny pinholes in thick sections and is fixed with the sprue size and position. Gas porosity leaves bubbles and is fixed with cleaner metal, dry crucibles, a complete burnout and casting under vacuum. If the holes appear in the same place on every tree, check the sprue first.

· 5 min

Buying guide

Diamond testers explained: which tester detects lab-grown (CVD) diamonds and moissanite

A standard thermal diamond tester reads both natural and laboratory-grown diamond as diamond, and can be fooled by moissanite. Separating moissanite needs an electrical conductivity test. Detecting lab-grown (CVD or HPHT) diamonds needs a screener, which checks the diamond type and refers possible lab-grown stones for further testing. A referral is not a verdict.

· 7 min

Technical

Burnout furnace for jewellery casting: the burnout cycle and how to choose a furnace

A burnout furnace heats the invested flask to remove the wax and leave a clean mould, then holds it at the casting temperature. Many gypsum investments for gold and silver peak at around 730 °C after a slow start, but always follow your investment maker's chart. Heating too fast in the first hour causes rough castings.

· 4 min

Buying guide

Gold testing machine price in India: karat meters, XRF analyzers and electronic testers compared

Gold testing machines range from about ₹1.35 lakh to ₹12.99 lakh including GST. A portable electronic karat tester costs ₹1,35,000. A benchtop XRF analyzer, which most jewellers call a karat meter, costs ₹6,45,000 for the Signet-PC, ₹8,95,000 for the Signet Si-Pin and ₹12,99,000 (special offer price; MRP ₹15,00,000) for the Signet FSDD. The difference is what each one reads, its published accuracy and what is included.

· 5 min

Technical

Wax injection defects: bubbles, short fills, flash and cracks, and how to fix them

Most wax pattern faults start at the injector and have a short list of causes. Bubbles come from a low wax level, unmelted wax, wet compressed air or fast injection. Short fills come from weak vacuum, missing vents or cold wax. Flash comes from too much pressure or uneven clamping. Change one thing at a time.

· 5 min

Technical

How to repair a broken gold chain with a laser welding machine

A jewellery laser welding machine repairs many broken chains by melting the chain's own metal at a spot as small as 0.2 mm, so the links beside the joint stay cool and keep their shine. Check whether the chain is solid or hollow first, close the link tightly, weld with short pulses and add filler wire only where there is a gap.

· 5 min

Technical

Using a gold melting machine: ten mistakes that crack crucibles and lose metal

Most gold melting problems come from a few habits: a damp crucible heated too fast, wet or dirty scrap, cold metal jammed into the crucible, holding the melt at full power and a neglected chiller. Our IG machines melt gold and silver, but capacity is rated in gold, so ask for the silver figure. Melting also does not purify gold.

· 5 min

Buying guide

How to check gold purity in India: hallmark, HUID, karat meters and XRF testing

Start with the hallmark: the BIS mark, a grade such as 22K916 and a six-character HUID that you can verify in the BIS CARE app. For a piece without a hallmark, or old gold you are buying, a non-destructive XRF test, often called a karat meter, reads the purity in under a minute. Fire assay at a hallmarking centre is the reference method. Home tests with a magnet, water or vinegar cannot tell 18K from 22K.

· 7 min

Semsons Tech guide Technical 7 min read

Technical

Castable resin casting problems: why 3D printed jewellery patterns fail, and how to fix them

When a casting from a 3D printed pattern fails, check five things before blaming the printer: that the resin is direct castable, that the print was washed and fully cured, that the burnout ramped slowly at the start, that the final hold was long enough for the load, and that the oven really reached its set temperature.

· 7 min

Semsons Tech guide Automation 7 min read

Automation

Setting laboratory-grown diamonds at scale: why automatic wax setting pays off

Laboratory-grown diamonds have the same crystal structure as natural diamonds, so an automatic wax setting machine sets them the same way. As their prices fall, designs carry more stones and setting becomes the bottleneck. Cast them in place with a stone-casting investment, a cooler burnout and slow cooling, keep treated colour stones out, and test-cast every new lot first.

· 7 min

Semsons Tech guide Compliance 7 min read

Compliance

Silver hallmarking in India: HUID, 925 purity testing and the machines you need

Silver hallmarking in India is still voluntary in 2026. Since 1 September 2025, any silver piece that is hallmarked must carry a six-digit HUID beside the BIS mark and a purity grade such as 925, and more than 90 lakh pieces have been hallmarked that way. For a silver maker, the practical steps are to test each lot before it goes for hallmarking, keep alloys separate, and keep your own marks apart from the hallmark.

· 7 min

Semsons Tech guide Compliance 8 min read

Compliance

HUID hallmarking in 2026: what jewellers must know about XRF testing and laser marking

A HUID hallmark has three parts: the BIS mark, the purity grade such as 22K916, and a six-digit code unique to the piece. It is mandatory for gold sold in 392 districts, and only a BIS-recognised hallmarking centre can apply it, after XRF screening and fire assay. A jeweller's own XRF analyzer checks each lot before it goes for hallmarking. A jeweller's own laser marker is for brand and lot marks, never the hallmark.

· 8 min

Buying guide

Laser soldering machine for gold jewellery: price in India, laser vs pulse arc, and how to choose

To weld broken gold for your business you need one of three tools: a torch or hydra flame with solder, a pulse arc welder, or a laser welding machine, which Indian jewellers call a laser soldering machine. The laser is the most precise and costs the most: it melts a spot as small as 0.2 mm under a microscope, so chains, prongs and set rings are repaired without heating the whole piece.

· 10 min

Semsons Tech guide Industry trends 9 min read

Industry trends

Gold at record prices: how jewellery manufacturers are switching to lightweight, studded and 9K/14K designs

Gold reached record highs in early 2026, and Indian jewellery demand fell 19% by weight in Q1 and 15% in Q2 while the money spent rose. The World Gold Council says buyers are shifting to lighter-weight, lower-carat and studded jewellery. For a manufacturer that means designing to a target weight, controlling more alloys such as 18K, 14K and 9K, and setting more stones in every piece.

· 9 min

Automation

How a double-station wax setting machine works, and when the X4 Pro Plus fits

A double-station wax setting machine sets stones into wax models on one worktable while the operator reloads the other, so the setting head barely waits. The X4 Pro Plus does this with four suction nozzles at ±0.02 mm, rated at up to 15,000 stones per hour on single-phase power. Here is how it works and how to tell whether it suits your workshop.

· 6 min

Semsons Tech guide Cash handling 7 min read

Cash handling

Fake ₹500 notes are rising: how to stop them at your cash counter

Banks found 1,41,907 fake ₹500 notes in 2025-26, up 20.5% in a year, and a fake note earns no credit when you deposit it. The answer is a check at the moment you take cash: a note counting machine with UV, MG and IR detection on every payment, and a hand check of any note it stops on.

· 7 min

Semsons Tech guide Buying guide 13 min read

Buying guide

The Ultimate Cash Counter Buying Guide: How to Choose the Right Note Counting Machine for Your Business

Start with one question: does your counter need a count of notes, or a rupee total of a mixed stack? Then compare the fake note checks, the half, chain and double note checks, the batch and add modes, the hopper size and the warranty. Here is what each function really does, with the Semsons Tech ST810 and ST2330 compared.

· 13 min

Semsons Tech guide Buying guide 9 min read

Buying guide

Induction melting machines: which capacity band fits your floor

It looks like a capacity question and it is really a power supply question. Three of the four machines need three phase — and no amount of wanting a bigger crucible changes what is coming into your building.

· 9 min

Semsons Tech guide Buying guide 9 min read

Buying guide

LCD, DLP or MJM: how to choose a jewellery 3D printer

Three technologies, six machines, five resins. What each one is for, the catalogue figures side by side, and the order to make the decision in.

· 9 min

Semsons Tech guide Buying guide 8 min read

Buying guide

Diamond setting machine price: what actually drives the number

Most of our machines are quoted rather than listed, and this article explains exactly why — plus every variable that moves your quotation up or down, so you can compare offers properly.

· 8 min

Semsons Tech guide Buying guide 11 min read

Buying guide

How to choose a diamond wax setting machine: a buyer's guide

Most buyers start with the wrong question. Here is the order the decisions actually need to be made in — throughput, then wax, then power, then footprint.

· 11 min

Semsons Tech guide Automation 10 min read

Automation

Wax setting vs hand setting: which is better, and how a machine raises productivity

For the small, repeated round stones in most production orders, wax setting on an automatic machine is better: thousands of stones an hour, every stone at the same depth and angle, and no drop late in the shift. Hand setting still wins for large centre stones, delicate gems, repairs and one-off pieces.

· 10 min

Would rather just ask someone?

Tell us what you produce and what is limiting your output. We will give you a straight answer, including when the answer is that you do not need a new machine.