Wax setting means putting the stones into the wax model of a piece before it is cast, instead of setting them into finished metal afterwards. When the metal is poured, it flows around each stone and locks it in. The piece comes out of casting with its stones already set.
That one change moves stone setting from the end of the line to the middle, and it is why many manufacturers of studded gold, silver and lab-grown diamond jewellery now set in wax. Here is what the term means, how the work flows from CAD to cast, and when it suits your pieces.
What wax setting means
In lost-wax casting, every piece starts as a wax model. Normally the wax is cast first and a setter then sets each stone into the metal, one at a time, with a graver and a pusher.
In wax setting, the stones go into that wax model instead. The set wax goes through investment and casting like any other wax. The stone stays in the mould while the wax burns out, and the metal fills the space around it. You will also hear it called stone setting in wax, stone-in-place casting or, for diamonds, wax set diamonds. They all mean the same thing.
Wax setting vs setting in metal
| Setting in metal (after casting) | Wax setting (before casting) | |
|---|---|---|
| When stones go in | After casting and cleaning | Before casting, into the wax |
| What holds the stone | Metal pushed over by the setter | Metal that forms around the stone in the casting |
| Speed | One stone at a time, by hand | Fast by hand in wax; much faster on a machine |
| Consistency | Depends on each setter and the time of day | On a machine, every seat is drilled the same way |
| Suits | Large stones, one-off pieces, delicate or heat-sensitive stones | Many small round stones: pavé, halos, bands, studded lines |
Setting in metal is not going away. Large centre stones and stones that cannot take casting heat are still set by hand at the bench. Wax setting takes over the small, repeated stones that eat most of a setter's day.
From CAD to cast: the six steps
- Design the piece in CAD with a seat for every stone. The seats in the file decide where each stone lands, so this is where good results start.
- Make the wax model. Print it on a jewellery 3D printer or inject it from a rubber mould. A clean, complete wax matters: a weak prong in wax becomes a weak prong in gold.
- Fix the wax on a base. The model sits on a round base with stud, held with two-part setting putty that you knead together and shape while it is soft. The stud fits the machine, so the base goes in the same way every time.
- Sort the stones by size into sorting trays. Each size band has its own tray and its own suction nozzle.
- Set the stones. On an automatic machine, the operator picks the design on the touchscreen and presses start. For every stone, the machine drills the seat, picks the stone up with a suction nozzle and presses it into the wax, within ±0.02 mm of where it belongs.
- Tree, invest and cast as usual, then finish the piece. Stone-in-place casting needs a little more care with investment, burnout and cooling; our guide to wax setting and casting lab-grown diamonds covers those settings.
Which stones can be wax set
Only stones that survive the heat of burnout and casting. In practice that means diamonds, both natural and lab-grown, and CZ. The trays for our setting machines are made for round natural diamonds, lab-grown diamonds (CVD and HPHT), CZ and synthetic rounds from 0.8 to 3.0 mm.
Coloured and treated stones are a different matter. Some lose colour or crack in the flask. If a design uses them, cast a few test pieces first, or set those stones by hand after casting.
Hand wax setting vs a machine
Wax setting can be done by hand: a setter warms a needle, opens the seat in the wax and presses the stone in under magnification. It is quicker than setting in metal, but it still depends on one person's eye and hand, stone after stone.
An automatic wax setting machine does the same three moves for every stone (drill, pick, press) at the same depth and angle each time. The four Semsons Tech machines run from a compact Pro Mini rated at up to 10,000 stones an hour to the double-head ST-HDSSM at up to 20,000. If you want the full comparison of hand and machine setting, read manual vs automatic diamond setting.
Is wax setting right for your pieces?
It usually is when most of these are true:
- Your designs carry many small round stones: pavé, halos, eternity bands, studded chains and earrings.
- You make the same design in quantity, not one piece at a time.
- Setting is where orders wait the longest, or where quality changes from setter to setter.
- You already work from CAD and 3D printed or injected waxes.
It suits you less if most of your work is large single stones, heat-sensitive gems or one-off designs. When you are ready to pick a machine, our guide to choosing a diamond wax setting machine walks through the decision.
Watch it explained in your language
Prefer Hindi, Gujarati or Bengali? Pick your language and WhatsApp opens with your request. Our team replies with a video that explains this machine and how it works.
- हिन्दी · Hindi यह मशीन कैसे काम करती है, इसका वीडियो हिन्दी में WhatsApp पर पाएँ।
- ગુજરાતી · Gujarati આ મશીન કેવી રીતે કામ કરે છે તેનો વિડિયો ગુજરાતીમાં WhatsApp પર મેળવો.
- বাংলা · Bengali এই মেশিন কীভাবে কাজ করে, তার ভিডিও বাংলায় WhatsApp-এ পান।
- English Get the video explanation in English on WhatsApp.
Where to see and buy it
These are the Semsons Tech automatic wax setting machines. Each link opens the full specifications and a quotation request.
| Machine | Key facts |
|---|---|
| Pro Mini | Compact single station, 3 nozzles Up to 10,000 stones an hour, single-phase power |
| PRO SERIES | Full-size single station Datasheet on request |
| X4 Pro Plus | Double station, 4 nozzles Up to 15,000 stones an hour |
| ST-HDSSM | Double station, double head, 8 nozzles Up to 20,000 stones an hour |
Want to watch stones go into your own wax? Book a demonstration at our Mumbai or Rajkot office, at your workshop or live on video, or call +91 98216 12340.